Sep 24,2026
Single-Phase Asynchronous Motors: Starting, Slip & Torque
Learn how single-phase asynchronous motors, or induction motors, use pulsating fields, capacitors, slip, torque, speed control and selection.
1. What Does “Single-Phase Asynchronous” Mean?
The term identifies both the electrical supply and the torque mechanism. Single phase means the motor receives one alternating voltage waveform from the supply. Asynchronous means the rotor turns at a speed below the rotating-field reference speed, so there is relative motion to induce rotor current.
A single-phase asynchronous motor is specifically an induction motor. It should not be confused with a universal motor, a shaded-pole synchronous clock motor, or an electronically commutated motor powered from a single-phase mains input. Those machines may use single-phase supply but operate by different electromagnetic principles.
| Motor category | Supply type | Rotor torque mechanism | Is it an asynchronous induction motor? |
|---|---|---|---|
| Resistance split-phase motor | Single-phase AC | Induced squirrel-cage rotor current | Yes. |
| Capacitor-start / PSC / CSCR motor | Single-phase AC | Induced squirrel-cage rotor current | Yes. |
| Shaded-pole motor | Single-phase AC | Induced squirrel-cage rotor current | Yes. |
| Universal motor | Single-phase AC or DC | Series-wound commutated armature torque | No. |
| Synchronous clock/timer motor | Single-phase AC | Rotor locks to synchronous field | No. |
| EC/BLDC motor with AC mains input | Rectified single-phase input + electronic inverter | Electronically commutated PM torque | No. |
2. The Pulsating Field and Double-Revolving-Field Theory
A main stator winding supplied by single-phase AC produces a field that reverses polarity and varies in magnitude along a fixed physical axis. The double-revolving-field theory represents this pulsating field as the sum of two equal constant-magnitude fields rotating at synchronous speed in opposite directions.
At standstill, the forward and backward fields induce equal rotor currents and produce equal but opposite torques:
T_net=T_f-T_b=0
This is the reason a bare single-phase induction motor is not self-starting. If the rotor is spun forward, the slip relative to the forward field becomes low while the slip relative to the backward field becomes high. The forward torque becomes larger than the opposing backward torque, and the motor continues accelerating in the initial direction.
All About Circuits describes this decomposition of the single-phase pulsating field into two counter-rotating field phasors and explains that their net starting torque is zero at standstill [1]. ANSYS also highlights that the forward and backward field strengths change when the machine is running, and that slip is central to the resulting total torque [3].
| Rotor condition | Forward-field slip | Backward-field slip | Net torque result |
|---|---|---|---|
| Standstill | s_f=1 | s_b=1 | Equal forward/backward torque; net torque is zero. |
| Forward rotation | s_f=s | s_b=2-s | Forward torque dominates; positive net torque. |
| Near normal running speed | Small s | Near 2 | Forward field sustains load torque; backward-field braking component is relatively small. |
| Reverse rotation | s_f relative to selected forward direction becomes large | Opposite field becomes favorable | Motor develops torque in the reverse direction. |
The forward and backward slips for a rotor moving in the intended forward direction are:
s_f=N_s-N_r/N_s=s
s_b=N_s+N_r/N_s=2-s
The net electromagnetic torque can be conceptualized as:
T_net=T_f(s_f)-T_b(s_b)
The exact torque components require the motor’s equivalent circuit, including main/auxiliary winding parameters and field decomposition. The expression is valuable because it explains why a single-phase machine develops usable torque once it already has direction.
3. Creating Starting Torque: The Auxiliary Phase
A single-phase asynchronous motor becomes self-starting by adding a second stator field component that is physically displaced from the main winding and time-shifted from the main-winding current. The objective is to approximate a two-phase rotating field during startup.
The most common method is an auxiliary winding placed at a different stator position. Its current is made out of phase with the main winding through resistance, a capacitor, or both. A shaded-pole motor uses a conductive shading ring instead of a separate auxiliary winding.
| Starting method | How it creates phase displacement | Starting torque capability | Typical use |
|---|---|---|---|
| Resistance split phase | Auxiliary winding has higher resistance/lower inductance than main winding | Moderate | Light pumps, blowers, office machines, easy-start loads. |
| Capacitor start | Start capacitor creates strong phase shift in auxiliary winding | High | Compressors, pumps, belt loads, higher-inertia starts. |
| PSC / capacitor run | Run capacitor remains connected continuously | Low to moderate | Fans, blowers, air handlers, continuous light-duty applications. |
| CSCR | Large start capacitor plus continuous run capacitor | High with improved running characteristics | Refrigeration, demanding pumps, higher-duty single-phase loads. |
| Shaded pole | Copper shading ring delays flux in part of each pole | Very low | Small fans, low-power appliances, simple direct-drive loads. |
ASPINA explains that a PSC motor uses separate main and secondary windings, with the secondary winding connected through a capacitor. The resulting time shift between winding currents creates a starting torque [2].
4. Main Components and Construction
A typical single-phase asynchronous motor shares many parts with a three-phase cage induction motor but adds a dedicated starting arrangement. The rotor is normally a squirrel cage made of aluminum or copper bars embedded in a laminated steel core. The stator contains the main winding and, for most designs, auxiliary/start winding components.
| Component | Function | Service/selection relevance |
|---|---|---|
| Main winding | Produces primary pulsating field and carries continuous running current | Its resistance, insulation, cooling, and voltage rating set continuous capability. |
| Auxiliary/start winding | Provides spatially displaced field for starting | May be continuous-duty (PSC) or intermittent-duty (capacitor start). |
| Squirrel-cage rotor | Carries induced rotor current and produces torque | Rugged and brushless; rotor condition is not externally adjustable. |
| Start capacitor | Produces high auxiliary phase shift/current for acceleration | Usually intermittent duty and must be disconnected when required. |
| Run capacitor | Remains in circuit while running | Must be AC continuous-duty rated and properly sized. |
| Centrifugal switch / relay | Removes start circuit after acceleration | Failure can cause no-start or rapid start-winding overheating. |
| Shading ring | Creates delayed local flux in shaded-pole motor | Simple but limits starting torque and reversibility. |
| Thermal protector | Opens circuit at unsafe temperature | Key defense against stalled rotor, poor cooling, and start-circuit faults. |
| Bearings and shaft | Support rotor and transmit load | Bearing load, alignment, vibration, and lubricant affect life. |
5. Capacitors and Phase Shift
Capacitors are central to high-performance single-phase starting because they shift auxiliary-winding current relative to the main-winding current. The capacitive reactance is:
X_C=1/2π fC
The actual phase angle is determined by the complete auxiliary circuit—capacitor, winding resistance, winding inductance, supply voltage, and motor speed—not by capacitor value alone. A capacitor with the wrong value can reduce starting torque, raise current, overheat the winding, or prevent proper start-switch operation.
| Capacitor arrangement | Electrical role | Operating duration | Key requirement |
|---|---|---|---|
| Start capacitor | Produces high phase shift and auxiliary current for starting torque | Brief/intermittent | Must have correct starting duty, capacitance, and AC voltage rating. |
| Run capacitor | Optimizes auxiliary current during running | Continuous | Must be a continuous-duty motor-run component. |
| PSC single capacitor | Serves as permanent auxiliary-phase element | Start and run | Balances simplicity, running behavior, and moderate start torque. |
| CSCR dual capacitor | Large start capacitor is removed; smaller run capacitor stays | Start plus continuous run | Requires reliable switch/relay and matched values. |
| No capacitor | Uses resistance split or shaded-pole method | Not applicable | Simpler but generally lower starting-torque performance. |
6. Synchronous Speed, Slip, and Rotor Frequency
The synchronous speed of a single-phase asynchronous motor is determined by the same frequency–pole-count relationship as other AC induction motors:
N_s=120f/P
The rotor runs below synchronous speed under forward motoring load. Its forward slip is:
s=N_s-N_r/N_s
The forward rotor-current frequency is:
f_r,f=sf
Once the motor is running forward, the backward rotating field sees a much greater relative speed. Its effective slip is 2-s, producing an opposing torque component. This internal backward-field effect is one reason single-phase induction motors can have lower power factor, lower efficiency, and different torque characteristics than a comparable balanced three-phase machine.
| Quantity | Formula | Meaning |
|---|---|---|
| Synchronous speed | N_s=120f/P | Speed of each rotating-field component. |
| Forward slip | s_f=(N_s-N_r)/N_s | Governs forward rotor EMF/current and useful torque. |
| Backward slip | s_b=2-s_f | Governs opposing backward-field torque once rotor moves forward. |
| Forward rotor frequency | f_r,f=s_ff | Induced-current frequency relative to forward field. |
| Backward rotor frequency | f_r,b=s_bf | Induced-current frequency relative to backward field. |
| Mechanical shaft power | Pshaft=Tω | Useful output from torque and speed. |
| Single-phase input power | Pin=VI\cos\phi | Real electrical input power. |
Worked forward/backward-slip example
Consider a 4-pole single-phase asynchronous motor supplied at 60 Hz and running forward at 1,725 rpm with 0.75 N·m shaft torque.
N_s=120×60/4=1,800\ rpm
s_f=1800-1725/1800=0.0416=4.16\%
s_b=2-0.0416=1.9584
f_r,f=0.0416×60≈2.50\ Hz
f_r,b=1.9584×60≈117.50\ Hz
Pshaft=0.75×2π×1725/60≈135.48\ W
The example shows why the two field components do not cancel once the rotor is moving forward. The forward field sees only low slip, while the backward field sees an effective slip close to 2. The actual forward and backward torque magnitudes still depend on the motor’s circuit parameters and auxiliary-winding configuration.
7. The Major Single-Phase Asynchronous Motor Types
Resistance split-phase motors
A resistance split-phase motor uses an auxiliary winding with a different resistance-to-inductance ratio from the main winding. The resulting phase difference is modest, so starting torque is moderate. The start winding is disconnected after the motor accelerates because its current density and heating are unsuitable for continuous duty.
Capacitor-start motors
A capacitor-start motor uses a high-capacitance start capacitor in series with the auxiliary winding. The greater phase separation produces higher starting torque, making this architecture suitable for pumps, compressors, and loads requiring stronger breakaway performance. The start capacitor and winding are typically disconnected near operating speed.
Permanent split capacitor (PSC) motors
A PSC motor retains the capacitor in circuit throughout running operation. It is simple and widely used for fans and blowers. ASPINA identifies the PSC as a split-phase induction motor with a permanently connected capacitor, as distinct from a capacitor used only during startup [2].
Capacitor-start/capacitor-run motors
A CSCR motor combines a high-value start capacitor with a continuous-duty run capacitor. It offers strong startup and improved running characteristics, at the expense of added components and switching complexity.
Shaded-pole motors
A shaded-pole motor uses a copper ring around part of a stator pole. Current induced in the ring delays flux in the shaded section, creating a weak sweeping field. It is cheap and robust but has low starting torque, modest efficiency, and a direction usually fixed by mechanical pole geometry.
| Type | Start system | Relative starting torque | Run configuration | Typical fit |
|---|---|---|---|---|
| Shaded pole | Shading ring | Very low | Single main winding plus shading ring | Very small fans and low-torque appliances. |
| Resistance split phase | Resistive auxiliary winding | Moderate | Start winding disconnected | Easy-start loads and compact general products. |
| PSC | Capacitor in auxiliary circuit | Low to moderate | Capacitor and auxiliary winding remain connected | Continuous fan/blower duty. |
| Capacitor start | Large start capacitor + auxiliary winding | High | Start circuit disconnected | Pumps, compressors, moderate/high-inertia starts. |
| CSCR | Start capacitor plus run capacitor | High | Run capacitor remains connected | Higher-demand compressors and pumps. |
8. Torque–Speed Curve and Starting Behavior
A single-phase asynchronous motor must generate more starting torque than the load’s breakaway torque and retain enough torque through acceleration. The motor’s total torque is the forward-field torque minus backward-field torque. The start circuit creates a field asymmetry so the initial net torque is positive.
At running speed, the forward field dominates, but the backward field does not disappear completely. The exact speed–torque curve depends on winding design, rotor resistance, capacitor values, supply voltage, and load. Use curves provided for the specific motor and driver/supply configuration, not generic holding or nominal values.
| Torque-curve term | Meaning | Selection requirement |
|---|---|---|
| Starting torque | Net torque at zero speed with start circuit active | Must exceed worst-case breakaway torque with margin. |
| Pull-up torque | Lowest torque during acceleration | Must remain above load torque throughout acceleration. |
| Breakdown torque | Maximum available torque before major speed collapse | Provides transient margin; not a continuous operating point. |
| Rated torque | Torque at rated speed, voltage, frequency, and thermal condition | Main continuous-duty design point. |
| Locked-rotor current | Current at zero speed | Determines start-component stress and protection sizing. |
| Pull-in speed | Highest speed at which direct start is possible for a given load | Defines safe start region. |
9. Speed Control: Practical Limits and Better Alternatives
Conventional single-phase asynchronous motors are usually designed for fixed line frequency and a narrow operating range. Their speed changes with slip, not directly with voltage. Reducing voltage can reduce torque substantially and may push the motor into an unstable or overheated operating region, particularly if its shaft-mounted fan is the main cooling source.
Some PSC and shaded-pole fan motors support approved multi-tap, capacitor-switching, or triac voltage-control methods. These methods should only be used with compatible motor/load combinations. Wide-range speed control, high low-speed torque, quiet operation, or closed-loop regulation is often better served by an EC/BLDC motor or a three-phase motor plus VFD.
| Speed-control approach | Suitable case | Benefit | Main limitation |
|---|---|---|---|
| Fixed-frequency operation | Standard mains motor duty | Lowest complexity | Speed changes only with load/slip. |
| Multi-tap winding | Fan/blower PSC motors | A few reliable discrete speeds | No continuous control; only designed taps are valid. |
| Voltage/triac control | Compatible fan-type loads | Low-cost speed reduction | Torque falls with voltage; heat/noise/stall risk. |
| Capacitor switching | Designed PSC motors | Discrete optimized speeds | Requires exact circuit values and manufacturer approval. |
| EC/BLDC replacement | Variable-speed appliance/fan/pump | Efficient wide-range control | Requires electronic drive and different system architecture. |
| Three-phase + VFD replacement | Larger variable-speed industrial load | Strong torque/speed control | Requires three-phase motor, VFD, and integration effort. |
10. Direction Reversal
In many split-phase and capacitor motors, direction is changed by reversing the relative polarity of the auxiliary winding with respect to the main winding. Reversing both windings together leaves their relative field relationship unchanged, so the rotation does not reverse.
Shaded-pole motors are generally not electrically reversible because the shading-ring geometry fixes the field sweep direction. Any reversal must follow the motor’s wiring diagram; incorrect rewiring can damage start components or create an unsafe machine rotation.
| Motor type | Direction reversibility | Usual method |
|---|---|---|
| Resistance split phase | Often reversible | Reverse auxiliary winding leads relative to main winding. |
| Capacitor start / CSCR | Often reversible | Reverse auxiliary/start circuit per manufacturer diagram. |
| PSC | Often reversible if leads are provided | Reverse auxiliary winding connection. |
| Shaded pole | Usually fixed | Direction set by physical shading-pole placement. |
| EC motor | Often software-defined | Command direction through electronics. |
11. Selection Workflow
Selecting a single-phase asynchronous motor requires more than matching voltage and power. The main question is whether its starting system can accelerate the actual mechanical load within the available thermal and electrical limits.
| Step | Define this first | Why it matters |
|---|---|---|
| 1 | Running torque, speed, and power | Establishes basic output requirement and pole count. |
| 2 | Breakaway torque and start condition | Selects shaded-pole, split-phase, PSC, capacitor-start, or CSCR topology. |
| 3 | Load inertia and acceleration time | Determines start-winding/capacitor duty and pull-up torque margin. |
| 4 | Supply voltage/frequency tolerance | Governs synchronous speed, torque availability, current, and component ratings. |
| 5 | Starts per hour and dwell time | Determines thermal accumulation in start winding, capacitor, and switch/relay. |
| 6 | Required speed adjustment | Determines whether a conventional motor is adequate or EC/three-phase VFD is preferable. |
| 7 | Ambient, airflow, moisture, dust, and mounting | Determines enclosure, insulation, cooling, and derating. |
| 8 | Reversal and braking need | Determines accessible leads, switch logic, and safe control architecture. |
| 9 | Noise/vibration target | Influences motor type, pole count, mounting, fan, and speed-control strategy. |
| 10 | Maintenance expectation | Evaluates capacitor, relay, switch, bearing, and service-access requirements. |
12. Thermal Management and Reliability
Single-phase asynchronous motors often experience their highest thermal stress during starting, stall, and low-speed voltage-control duty. At standstill, there is no back EMF and little shaft-fan airflow, but the main and auxiliary circuits can draw high current. The thermal protector must protect against a failed start, blocked load, capacitor failure, poor ventilation, or repeated rapid cycling.
| Reliability risk | Typical cause | Preventive action |
|---|---|---|
| Failed start capacitor | Aging, heat, overvoltage, incorrect replacement | Use correct intermittent-duty capacitor; verify start duration and ventilation. |
| Failed run capacitor | Long-term dielectric degradation or high ambient | Use approved continuous-duty part and inspect critical systems periodically. |
| Start switch/relay stuck closed | Wear, contamination, wiring fault | Verify cutoff speed and start current; replace defective devices. |
| Humming/no start | Open auxiliary winding, capacitor failure, low voltage, jammed load | Isolate safely; check supply, capacitor, winding continuity, and shaft freedom. |
| Winding overheating | Overload, repeated starts, poor cooling, voltage mismatch | Measure current/voltage/temperature under actual duty; derate or resize. |
| Bearing noise/failure | Contamination, misalignment, belt tension, lubrication loss | Inspect mounting, shaft loads, seals, alignment, and lubrication. |
| Low-speed thermal damage | Voltage control reduces fan airflow while torque demand persists | Use approved speed range, external cooling, or EC/three-phase alternative. |
13. Applications
Single-phase asynchronous motors are attractive where single-phase utility power is available, the required power is modest, and the load is well matched to a specific start topology.
| Application | Load behavior | Typical motor choice |
|---|---|---|
| Small ventilation fan | Low starting torque, continuous duty | Shaded-pole or PSC. |
| HVAC air-handler blower | Extended fan operation, discrete speeds | PSC or EC upgrade. |
| Domestic water pump | Moderate breakaway torque | Capacitor-start or CSCR. |
| Refrigeration compressor | High start torque and cycling duty | Capacitor-start or CSCR. |
| Small workshop machine | Moderate torque, mostly fixed speed | Split-phase, capacitor-start, or appropriate gearmotor. |
| Garage-door opener | Intermittent, reversible travel | Reversible capacitor-start/PSC with limit and safety control. |
| Appliance fan or blower | Low-to-moderate torque | PSC, shaded-pole, or EC according to efficiency/noise target. |
| Variable-speed ventilation | Wide speed range and energy efficiency | EC/BLDC often preferred over conventional asynchronous motor. |
14. Troubleshooting Guide
A reliable diagnosis begins by separating electrical, start-circuit, mechanical, and thermal causes. Do not replace a capacitor or motor without checking supply voltage, load freedom, winding continuity, current, and start-switch behavior.
| Symptom | Likely causes | First diagnostic actions |
|---|---|---|
| Motor hums but does not start | Failed capacitor, open auxiliary winding, stuck load, undervoltage | Check shaft freedom, supply voltage, capacitor condition, auxiliary circuit. |
| Starts only after manual spin | Missing effective auxiliary phase | Inspect capacitor, start winding, switch/relay, wiring polarity. |
| Slow acceleration | Low supply voltage, weak capacitor, high load inertia, wrong motor type | Measure voltage during start; compare load to torque curve; check start circuit. |
| Starts then overheats | Start circuit not disconnecting, overload, blocked cooling | Verify switch/relay timing and start-winding current; inspect airflow/load. |
| Wrong direction | Auxiliary winding connection reversed or miswired | Confirm wiring diagram; reverse only the approved auxiliary connections. |
| Speed drops excessively under load | Overload, low voltage, capacitor degradation, mechanical friction | Measure current/voltage, inspect load and capacitor, check bearing/drive friction. |
| Excessive noise/vibration | Bearing wear, resonance, loose mounting, capacitor/control issue | Inspect bearings/mount/base; compare noise by speed/load; verify supply/control. |
| Repeated thermal-protector trips | Stall, frequent cycling, poor ventilation, incorrect capacitor | Review starts-per-hour, thermal duty, load condition, and cooling environment. |
Conclusion: Starting Design Defines the Single-Phase Asynchronous Motor
A single-phase asynchronous motor works by the same induction principle as a three-phase cage motor, but its pulsating main field creates a unique constraint: it cannot generate net starting torque without an auxiliary directional field. Double-revolving-field theory explains this clearly—two equal counter-rotating fields cancel at rest, while a capacitor, resistive auxiliary winding, or shaded pole breaks the symmetry and starts the rotor.
For dependable selection, begin with breakaway torque, acceleration, supply quality, duty cycle, and required speed control. Choose the start topology that provides the necessary torque, then validate the capacitor, auxiliary winding, switch/relay, thermal protector, mechanics, and real operating environment as one system. If the application needs quiet, efficient, wide-range speed control, consider an EC/BLDC or three-phase VFD architecture before committing to a conventional single-phase asynchronous design.
References
Editorial note: This article is intended for engineering education and preliminary product selection. Final motor, capacitor, start switch or relay, wiring, speed-control method, thermal protection, enclosure, and safety selections must be confirmed with supplier documentation and tested in the intended product environment.
Related News
LATEST
INFORMATION
Get the latest product information of the company
NAVIGATION
PRODUCTS
CONTACT US
Telephone: +86 13305761511
Email: info@cntecho.com
Add: RM. 602, BUILDING B, NO.1551 SHUANGSHUI RD., LUQIAO DIST., TAIZHOU CITY, ZHEJIANG, CHINA
Copyright © 2026 TECHO ELECTRICAL & MECHANICAL (TAIZHOU) CO., LTD. All Rights Reserved.